View Cart “12V BATTERY PROTECTOR (SBS01205D)” has been added to your cart.
6-64AL_front_25
BatMan_mainblock_diagram_usb6-64AL_dimensions_25top_01connection_diagram_lvd_AL64BatMan_main_InfoBatMan_main_configBatMan_main_io_configsbs6-64ALxx_specsconnection_diagrams_for_lvd_mcu-OVDconnection_diagrams_for_lvd_mcu-LVDconnection_diagrams_for_lvd_mcu-IDIODEconnection_diagrams_for_lvd_mcu-B2B

SBS 6-64AL-USB

122.00181.00

Clear

Product Description

Battery Protector (Low/Over Voltage Disconnect)
in strong aluminum case with USB for easy setup
model: SBS 6-64AL-USB
To protect batteries against over discharging.
For high amp systems where safety and ease of use are in first place.
Description
  • Low power MCU with 12 bit ADC conversion and micro USB connector on board.
  • Fully customizable with BatMan manager software for any battery requirements.
  • Solid state switch with ‘soft start’ feature (multiple N-ch MOSFETs on positive side).
  • Draws only 0.7 mA when OFF and 1.5 mA when ON state!!!
  • Two color (red, green) LEDs with multiple status indication patterns.
  • Remote ON/OFF socket (JST PH 2.0-3 Pin). Connector with 15cm cable included.
  • Two open drain (aka “open collector”) outputs socket (JST PH 2.0-3 Pin) for alarm or other needs. Connector with 15cm cable included.
Features
  • Real-time input voltage and status monitoring in BatMan manager software.

Device input voltage, status and all parameter changes are applied in real-time. Multiple devices simultaneously are supported.

  • Wide range Cut-Off and Reconnect voltage level adjustments.

The following set points can be set:

  1. Low voltage cut-off  and reconnect with or without delay from 10 ms to 10 min
  2. Over voltage cut-off and reconnect with or without delay from 10 ms to 10 min
  3. Working range min, max. This gives immediate action without delay in case you set delays for LVD or OVD cut-off, but voltage drops too fast.

All parameter changes are applied in real-time.

  • Remote control connector to force ON/OFF states.
If you short these pins to GND (black wire) than you will force the module in one of ON/OFF states.
OFF pin has higher priority. If both are shortened then module will be in OFF state.
This is handy if you need to control the load or use this module just as relay in any DC environment.
Normally you can leave these pins opened.
It is also possible to override these pins in manager software.
  • Two open drain outputs to drive alarm device or other needs.

Output 1 is active when delay before cut-off is used. This output can handle max 100 mA loads and is polyfuse protected.

Output 2 currently not used, but may be used in feature.
  • Thermal protection.

Will cut-off if module temperature rises above 80° C. This is true even in forced ON state.

With new software (BatMan 1.3.0.0) you can even set custom temperature working range from -30 to 90° C (-22° to 194° F)

  • Over-current protection. (NOT short circuit protection – please use circuit breaker for that.)

Will cut-off if over-current condition occurs. This feature is highly configurable, but has very rough current step gradation (one step is 1/3 of device max amp value).

  • Will act like ‘ideal diode’.

If reverse current flow through MOSFET body diode is detected then device is forced to turn ON to eliminate power dissipation on body diode.

  • Can be used as SSR relay.

It can be easily configured as relay. Just drive it through remote port.

  • Low self consumption

This module has very low working current (max 0.7 mA when OFF and 1.5 mA when ON)

  • Firmware upgrade is possible

It is possible to upgrade devices firmware. If you find a bug or you need new features – send a message to support@bed-electronics.com and it will get fixed.

Notes

Here you can view a comparison table (as PDF doc.) for all actual models.

 

 

Additional Information

Weight 0.5 kg
Dimensions 15 x 10 x 5 cm

Reviews

There are no reviews yet.

Be the first to review “SBS 6-64AL-USB”